Water and building services
SX 50-160 Interactive 3D Model
Close-coupled end-suction pump to EN 733 size 50-160: cast iron volute, closed bronze impeller and a 5.5 kW two-pole IE3 motor on one stainless shaft. 30 m³/h at 34 m.
STRAVIK is a fictional brand. This is a Proofscene demo product.
About the SX 50-160
The SX 50-160 is the kind of pump every building, factory and farm runs: water comes in along the shaft through the DN65 suction, the impeller throws it outwards, and the spiral volute turns that speed into pressure before the DN50 discharge on top.
The impeller sits straight on the motor's extended stainless shaft, so there is no coupling to align. A rubber-bellows mechanical seal (carbon on silicon carbide) keeps the water in, and the cast iron lantern between pump and motor has two windows so the seal can be checked without taking anything apart.
Parts in the 3D model
- Volute casing
- Casing wear ring
- Impeller
- Impeller key
- Impeller washer
- Impeller nut
- Casing cover
- Casing O-ring
- Lantern
- Flinger
- Drain plug G3/8
- Sealing washer G3/8
- Plug G1/4 (3)
- Sealing washer G1/4 (3)
- Shaft
- Seal spring retainer
- Seal spring
- Seal bellows
- Seal rotating face
- Seal stationary seat
- Seat O-ring
- Drive-end bearing 6308, outer ring
- Drive-end bearing 6308, inner ring
- Drive-end bearing 6308, ball (8)
- Drive-end bearing 6308, cage
- Non-drive-end bearing 6208, outer ring
- Non-drive-end bearing 6208, inner ring
- Non-drive-end bearing 6208, ball (9)
- Non-drive-end bearing 6208, cage
- Motor housing
- Stator core
- Stator winding
- Rotor core
- Rotor cage
- Drive-end shield
- Non-drive-end shield
- Wave spring washer
- Cooling fan
- Fan circlip
- Fan cowl
- Motor foot (2)
- Nameplate
- Lifting eye bolt
- Terminal box
- Lid gasket
- Terminal box lid
- Lid screw M5 x 35 (4)
- Terminal block
- Terminal stud M5 (6)
- Delta link (3)
- Terminal nut M5 (6)
- Cable gland M32
- Blanking plug M25
- Casing bolt M12 x 45 (8)
- Flange bolt M12 x 35 (4)
- Tie screw M8 x 325 (4)
- Foot screw M8 x 45 (4)
- Cowl screw M5 x 10 (3)
- Nameplate drive screw (4)
Technical specifications
- Duty point
- 30 m³/h at 34 m Best efficiency, water at 20 °C
- Flow range
- 10–45 m³/h
- Speed
- 2900 min⁻¹ 50 Hz, two-pole
- Liquid temperature
- −20 to +120 °C
- Pressure rating
- PN16
- Motor
- 5.5 kW, IE3 IEC 132S, 400 V 3~, two-pole
- Mounting
- Close-coupled B5 flange FF265, one-piece shaft
- Suction / discharge
- DN65 / DN50 EN 1092-2 PN16 flanges
- Impeller
- Ø169, closed, 6 vanes
- Size class
- EN 733 50-160
- Casing
- EN-GJL-250 cast iron
- Impeller
- CuSn10 bronze
- Shaft
- 1.4021 stainless steel
- Shaft seal
- Carbon / SiC / EPDM EN 12756, d1 = 28 mm
- Mass
- 100 kg Calculated from the CAD
- Overall size
- 690 × 300 × 360 mm Length × width × height, from the CAD
STRAVIK is a fictional brand and the SX 50-160 a demonstration product built by Proofscene. Its figures are illustrative values typical of an EN 733 50-160 pump; masses and sizes are measured from the demo CAD.
Interactive 3D product demos by Proofscene · Build one for your product